Appliance Testing Equipment

Ball Pressure Test Apparatus

Ball Pressure Apparatus is used for testing parts of non-metallic materials for resistance to heat. It is applicable to electrotechnical equipment, its subassemblies and components, and to solid electrical insulating materials except for ceramics.

Drop Test Apparatus

Package Impact Drop Testing Machines used to measure the dropping impact incidence when the package in using, transportation and decorating. it also can undertake edge and angle test to ensure the complete performance evaluation for the package.

Test Corner

Test Corner can be used to the temperature test of all kinds of electronic products supply, in conformity with the standards requirement of the environmental conditions.

Pendulum Impact Test Apparatus

Pendulum impact hammer is used for testing electrical and electronic equipment resistance to impact test.

Pendulum Impact Test Apparatus

Spring Operated Hammer

Hammers are available in single force selections or a Universal Spring Hammer that offers five selectable impact energies.

Cord Anchorage Torque Testing Machine

Appliances provided with a supply cord, and appliances intended to be permanently connected to fixed wiring by a flexible cord, shall have a cord anchorage. The cord anchorage shall relieve conductors from strain, including twisting, at the terminals and protect the insulation of the conductors from abrasion.

Cord Flexing Test Apparatus

This test apparatus checks the protection of the supply cord where it enters the appliance. Appliances provided with a supply cord that is moved while in operation shall be constructed so that the supply cord is adequately protected against excessive flexing where it enters the appliance.

Tumbling barrel Test Apparatus

The Tumbling Barrel Tester simulates repeated falls that may occur to such devices as connectors or small remote control units which are normally attached to cables during use.

Microwave Operating Mechanism

The microwave operating mechanism is used for microwave door endurance test its test for door life.

Stability Test Turn Table

This device is designed and manufactured in accordance with the IEC60335-1 clause 20.1.It is used to test the stability of an apparatus that requires a surface in order to work. The device consists of a surface and an angle adjusting device, with angles 0～15°adjustable.

Stability Test 800N

Drop overturned testing equipment is mainly used to drop product in 800N force condition to test whether a sample will be inclined, overturn or not.

Humidity Chamber

Laboratory Temperature Humidity Control Stability Test Environmental Chamber for Battery are ideal for the safety testing of lithium batteries, to shelf-life testing of sensitive electronics and pharmaceuticals. Temperature Humidity chambers offer simulated, real-life environments to test against various temperatures and humidity.

Hot Air Oven

Hot Air Oven for Battery are ideal for the safety testing of lithium batteries, to shelf-life testing of sensitive electronics and pharmaceuticals. Hot Air Oven offer simulated, real-life environments to test against various temperatures.

Scratch abrasion resistance test apparatus

Scratch abrasion resistance test apparatus is applicable to solid insulation appliances and similar products of accessible parts or PCB scratch test to ensure that the material has sufficient strength without being sharp tool pierced. The device is stable, one-button operation is specialized laboratory testing equipment. Socket Gauge/ Plug Gauge

Socket Gauge/ Plug Gauge

Specification:- ⦁ Gauge Male and Female ⦁ Material Totally S.S. 304 ⦁ Dimension as per standard Standard:- BS546

Hot Temperature Bath

Specification:-

  • Double-wall Bath
  • Inside S.S 304 and outside M.S. material
  • Temperature – 250 °C ± 2°C
  • Control by PT 100
  • Supply 230 / 220

Cold Temperature Bath

Specification:-

  • Double-wall Bath
  • Inside S.S 304 and outside M.S. material
  • Temperature – 250 °C ± 2°C
  • Control by PT 100
  • Supply 230 / 220

Deflection tester / Screw less Terminals Test Setup

Specification:-

  • Material Aluminum with polish
  • Angle meter 360° Degree
  • Weight 1.5 N and 2.5N
  • Scale including

Free Fall Impact Test Apparatus

Free Fall Impact is used to carry on the anti-impact ability test to the electrical home appliances and accessories or electronic electrical products or accessories.

Temperature Rise Test Setup

AC DC Source is suitable for power department, measuring department, quality control department, research units, the institution of higher learning, electric energy meter, power distribution terminals, power supply management, load control, power quality

Tensile Test Apparatus

The Tensile test apparatus application checks that all material strength like a gland, MCB, RCCB, Plug, Cable etc

Secureness Test Apparatus

The Secureness Test Apparatus application is Checking of the connector, MCB,RCCB, Lug cable clamping.

Cable Gland Retention test Apparatus

The Cable Gland Impact Test apparatus is use for gland Strength test.

Cable Gland Anchorage pull test apparatus

The Anchorage pull Test apparatus is use for gland pull test.

Cable Gland Anchorage Twist Test apparatus

The Anchorage pull Test apparatus is use for gland pull test.

Cable Gland Impact Test apparatus

The Anchorage pull Test apparatus is use for gland pull test.

JOINTED TEST FINGER ( TEST PROBE B)

  • Sphere Dia = 50 mm
  • Handle = Ø10 X 100 mm length
  • Guard = Ø45 X 4 mm thickness

RIGID STEEL ROD DIA. 2,5 (Test probe C)( IP 3X)

  • Length of test Rod = 100 mm
  • Test Rod Dia = 2.5 mm
  • Diameter of Sphere = Ø35 mm
  • Length of Handle = 100 mm
  • Handle Dia = 10 mm

RIGID STEEL WIRE DIA. 1 (Test probe D) ( IP 4X)

  • Length of test Rod = 100 mm
  • Test Rod Dia = 1 mm
  • The diameter of Sphere = Ø35 mm
  • Length of Handle = 100 mm
  • Handle Dia = 10 mm

TEST SPHERE DIA. 50, 0.51 kg ( Test probe 1)

  • Sphere Dia = 50 mm
  • Weight = 0.510 kg

RIGID SPHERE DIA. 12.5 (Test probe 2)(IP2X PROBE)

  • Sphere Dia = 12.5 mm
  • Handle = Ø10 X 100 mm length

RIGID TEST FINGER ( TEST PROBE 11)

  • Knurled Finger Diameter = 12 mm
  • Knurled Finger Length = 80 mm
  • Baffle Plate Diameter = 50 mm
  • Baffle Plate Thickness = 5 mm

LONG TEST PIN DIA (TEST PROBE 12)

  • Test probe diameter: 4mm
  • Test probe length: 50mm
  • Baffle plate thickness: 4mm
  • Baffle plate diameter: 25mm
  • Handle length: 20mm
  • Handle diameter: 10mm

TEST PIN DIA (TEST PROBE 13)

  • Test probe Flat: 3X 1 mm
  • Test probe length: 80mm
  • Handle length: 80mm

TEST PROBE 17

  • Test probe diameter: 0.5mm
  • Test probe length: 20mm
  • Handle length: 80mm
  • Handle diameter: 10mm

SMALL FINGER PROBE dia. 8.6 (TEST PROBE 18)

  • Above 36 months
  • Finger Dia – 8.6 mm
  • Finger Radius – 4.3 mm
  • Finger Total Length – 57.9mm
  • Finger single section length – 19.3 mm
  • Arm diameter – 38.4 mm
  • Arm Length – 101.6 mm
  • Extension rod diameter 38.1 mm
  • Extension rod diameter – 451.6 mm

SMALL TEST FINGER dia 5.6 mm (test probe 19)

  • Material S.S, P.P
  • Under 36 months
  • Finger Dia – 5.6 mm
  • Finger Redius – 2.8 mm
  • Finger Total Length – 44mm
  • Finger singal section length – 14.7 mm
  • Arm diameter – 25.9 mm
  • Arm Length – 101.6 mm
  • Extension rod diameter 25.4 mm
  • Extension rod diameter – 464.3 mm

TEST PROBE 31 ( Ground Probe )

  • Rod Diameter: 25mm
  • Rod Length: 80mm
  • Plate Former Diameter: 60mm
  • Plate Back Diameter: 110
  • Total Length: 150

TEST PROBE 32 Dia. 25 mm (AUTO 32)

  • Test probe diameter: 25 mm
  • Test probe length: 80mm
  • Handle length: 80mm

TEST PROBE 41 ( TEST THORN PROBE )

  • Road diameter: - 30 mm
  • Cone length: - 21.5 mm
  • Metal rod length 80 mm
  • Handle Diameter: - 50 mm
  • Handle length: - 80 mm

TEST PROBE 43

  • Test bar diameter: 50mm
  • Test bar thickness: 5mm
  • Handle material PP

Articulated Test Finger

  • Test Finger Length: 234mm
  • The Bending Part Length: 30/30/40mm
  • Material S.S. 304 and Nylon

Wedge Probe UL 60950

  • Length: 300mm
  • Width: 50mm
  • Bendable Section: 30/30/40mm
  • Material: S.S. 304

UL 507 PA160B Test Probe

  •  Total Length: 88.9mm(3.5 inch)
  • Head Length: 25.4mm(1 inch)
  • Head Radius: R 3.175mm(1/8 inch)
  • Former Head Diameter: 12.7mm(1/2 inch)
  • Tail Diameter: 25.4(1 inch)

Test Finger Nail Probe

  • Test Nail
  • Probe Length = 80 mm
  • The angle of The Finger Nail = 37o Degree
  • Diameter of Test Probe = Ø12 mm

75mm test probe

  • Probe Diameter: 40mm
  • Probe Length: 70 mm
  • Materials: S.S. 304 and Nylon

Mandrel test apparatus

This device is used to test the Insulation anti damage strength verification for non separable thin layer materials.

Other Services

  • Cable Testing Equipment

    Tensile Test ApparatusThe Tensile test apparatus application is check that all material strength like a gland, MCB, RCCB, Plug, Cable,etc Cold Bending Test ApparatusThe CKE cold bending test apparatus is

    Read More

  • PV Module Solar Equipment

    PV Module cut Susceptibility testing machineIt's to determine whether any front and rear surfaces of the module of polymeric materials are capable of withstanding routine handling during installation and maintenance

    Read More

Full list of Services