Cable Testing Equipment
Tensile Test Apparatus
The Tensile test apparatus application is check that all material strength like a gland, MCB, RCCB, Plug, Cable,etc
Cold Bending Test Apparatus
The CKE cold bending test apparatus is used for the cold bend test of the circular insulation wire core whose diameter is small and the sector-shaped insulation wire core which can not be used for a dumbbell. The apparatus shall be held in a refrigerator before and during the test.
Cold Impact Test Apparatus
The CKE cold bending test apparatus is used for the cold bend test of the circular insulation wire core whose diameter is small and the sector-shaped insulation wire core which can not be used for a dumbbell. The apparatus shall be held in a refrigerator before and during the test.
Cold Elongation Test Apparatus
Cold elongation test apparatus is applicable for the insulating sheath of the high polymer material, electric wire, rubber, and plastic to do the tensile test at the environment
Dumb-Bell Dia
The Dumbbell Dia is a replaceable blade cutter system that is developed as an ideal cutter to punch out a test piece of high polymer materials, such as, rubber, plastic, etc, and other materials.
Hot Deformation Test
The CKE Heat deformation test apparatus is use for Plastic and insulation for strength in oil with high temperature.
Cable Pressure Testing High Temperature
The CKE Cable Pressure Testing High Temperature that is used for the deformation of insulation and sheath of electric cable under pressure and temperature
H.V. Tester
The CKE H.V. Tester is use for specially checking for electrical material strength.
Hot Air Oven
Hot Air Oven for Battery are ideal for the safety testing of lithium batteries, to shelf-life testing of sensitive electronics and pharmaceuticals. Hot Air Oven offer simulated, real-life environments to test against various temperatures.
Wrapping /Torsion Test Apparatus
During the armoring process and subsequently, during laying of the cable, the armor wires are subjected to torsion stress. The test is conducted to evaluate the torsion resistance of the wire.
AC/DC Power Source
AC DC Source is suitable for power department, measuring department, quality control department, research units, institution of higher learning, electric energy meter, power distribution terminals, power supply management, load control, power quality
Two Flexing Test Apparatus
The CKE Two pulley flexing test is conducted to ascertain the capability of flexible cables to withstand flexing and other mechanical stresses occurring in normal use
Cable Hot Set Test Apparatus
The CKE Hot set test apparatus is used for insulation elongation test in a hot atmosphere.
Dielectric Strength Test Jig
This device is used to test the dielectric strength of the insulating material.
Conductor Resistance Testing
The fixture and conductor resistance tester or dual-arm DC bridge used to detect the conductor resistance. The fixture has a potential fixture and a current fixture to ensure the accuracy of the measured conductor current resistance
Cold Chamber
The CKE Cold chamber is widely used to test materials performance in low temperature test condition.
Ageing Oven 4 Tube
The CKE Ageing Oven is widely used to test materials performance in high temperature test condition.
Abrasion Test Apparatus
The CKE Abrasion test apparatus is use fore abrasion test of cable.
Flexing Test Apparatus
The CKE Flexing test apparatus is used for the cable flexing test.
Cable Slicer Fixture
⦁ Material Structure M.S. fully powder coated
⦁ Complete clamping wise
⦁ Sharp blad
⦁ Drive by motor
Cold Impact Test Apparatus
Due to constant exposure of cables to low temperature or frost conditions when laid in areas subjected to low temperature, the insulation or sheath of the cables becomes hard and brittle. Any impact on the surface of the sheath or cable under these conditions may fracture the insulation, thus making it weak or causing it to fail
Water Resistance testing - Mechanical properties of sheath after water
- Internal material S.S. 304
- External material m.s. fully powder coated
- PT 100 sensor
- Controlled by PLC
- Power Supply: 440 Vac 50-60Hz,Three Phase
- Size : 1000X 1000X 1000mm (L X B X H)
Other Services
-
Light Testing Equipment-1
Torsion Test ApparatusSpecification: Direct reading type on a graduated scale fitted with B-22d, E27, E14 lamp cap holders. Range: 0 – 4 Nm, 0 – 1.4 Nm Size: 400 x
-
Appliance Testing Equipment
Ball Pressure Test ApparatusBall Pressure Apparatus is used for testing parts of non-metallic materials for resistance to heat. It is applicable to electrotechnical equipment, its subassemblies and components, and to